Tomatoes are fun to grow and, of course, exceptionally delicious to eat. We’ve put together some tips for supporting and pruning your tomato plants to ensure a bigger, better harvest.
Supporting Tomatoes
Whether you’re growing your tomatoes indoors or out, you’ll need to give plants the right type of support. Some tomatoes need more support than others. Indeterminate types (also known as vining or cordon tomatoes) grow to head height and beyond, necessitating tall, sturdy supports, while bush (or determinate) tomatoes grow up to about three feet or one meter high and therefore require less support. Falling in between are semi-determinate, or intermediate types of tall bush tomatoes.
Cordon Tomatoes
Cordon tomatoes can be grown against tall canes or stakes or, in a greenhouse, twisted around string.
Firmly secure canes or stakes into the ground so they will be able to support the considerable weight of fruit-laden plants and withstand sudden gusts of wind. Push the supports into the ground before planting to avoid damaging the roots. Tie stems to their canes at regular intervals, leaving enough slack for the stem to continue growing in girth. Secure a tie just above a truss, as this will support the weight of fruits better than a tie secured below a truss. Use string or strips of soft material for the ties. Fully loop the tie around the cane before tying in the stem.
String supports are easy to set up. Dangle string directly from the greenhouse’s framework, or from a horizontal length of string secured and stretched taut between the gable ends. Bear in mind that the greenhouse will be bearing the entire weight of the plants so it must be strong enough for the job, and the string must be stronger than average garden twine which can snap easily.
Loop the string around the rootball of the tomato plant at planting time to secure the string in place. The string will be further anchored into the soil as the roots grow. As plants reach up, twist the string around the stem, completing a full loop around the stem every two leaves. When you reach a truss, tuck the string above or behind it, never below it.
Cordon tomatoes can also be trained up a wigwam structure, one plant to each cane.
Bush Tomatoes
In theory bush tomatoes do not need support, but left to their own devices plants can be weighed down onto the ground by heavy fruits, increasing the chances of slug damage, disease and fruit spoil.
Tie plants to sturdy stakes to keep them from flopping over. Alternatively, secure two parallel rows of horizontal canes to short, upright stakes hammered into the ground. Plant the tomatoes in between the two rows of canes. Lift up the branches and drape them over the canes as they grow.
How to Make Tomato Cages
Tomato cages offer fuss-free supports for bush and semi-determinate tomatoes. You can buy purpose-made cages, but it’s easy to make your own from concrete reinforcing mesh. The 6-inch (15cm) squares will allow you to easily flex the mesh into a tube to make your cage, and offer easy access to your tomatoes. They’re inexpensive to make, and can be reused for many years.
Start by cutting a length of mesh five to six feet long (150-180cm). When rolled into a tube this will give a cage diameter of 18 to 22 inches (45-55cm) - tight enough to support a plant while giving it enough room to expand. Use sturdy wire- or bolt cutters to make the cuts, and wear gloves to protect your hands from snagging cuts.
Once cut, carefully roll the length of mesh into a tube. Tie the ends together with heavy gauge wire or string to give a close hold. Now cut off the bottom wire from the cage to leave just the vertical wires sticking out. These wires can be used to push the cage into the ground. For added stability, tie the cage to a vertical length of rebar or similar sturdy upright. You can also pin the bottom wire to the ground with tent pegs.
Position your tomato cage by lowering it over the top of a plant. Pull through any stray branches. As the plant grows, encourage growth upwards through the centre of the cage. Fruiting trusses can be left to grow outside of the cage to make picking even easier. At the end of the season simply unfurl the mesh and store flat to save space.
How to Prune Tomato Plants
Tomatoes require regular pruning for the best results. This includes pruning trusses to remove excess fruits, removing unproductive lower leaves, and removing sideshoots, or suckers.
Truss Pruning
Removing developing fruits from trusses may seem counterintuitive but there are a few reasons to do this. First, thinning the fruits within the trusses of prolific fruiters such as cherry tomatoes will ensure those that remain grow larger. For varieties bearing particularly heavy fruits, such as the beefsteak tomatoes, thinning fruits to just three per truss will reduce the weight of the truss and make it less likely to snap away from the stem.
Prune trusses by snipping off the fruits with sharp scissors while they are still small.
Removing Leaves (Cordon Tomatoes)
Remove all leaves below the lowest ripening trusses of cordon tomatoes. These older leaves will divert the plant’s energy away from producing more flowers and fruits, while reducing air circulation and light penetration. Remove the leaves by pulling the leaf sharply up then down so it comes away from the main stem. Support the stem as you do this.
Removing Sideshoots (Cordon Tomatoes)
Also known as suckers, sideshoots on cordon tomatoes distract the tomato from producing flowers and fruits, and must also be removed. Sideshoots appear at the point where a leaf joins the main stem. Remove them by wiggling them from side to side then using your thumb to snap them out. Remove sideshoots while they are still young, working from the bottom of the plant up.
It needn’t take long to complete these simple training and pruning tasks - it’s a once-a-week job and at the same time you can inspect your plants and check on the progress of your ripening tomatoes. What system do you use? Drop us a comment below and tell us.